求救！

[sneaker]

Bindings 上得實得滯，用盡力都扭唔開之餘，當中兩粒螺絲既十字位損毀晒，因為試過用電批鑽，可惜越鑽粒螺絲既十字位越爛，現在已經上唔到，拆唔到個 binding， 點算呢？

[Mike]

Bindings 上得實得滯，用盡力都扭唔開之餘，當中兩粒螺絲既十字位損毀晒，因為試過用電批鑽，可惜越鑽粒螺絲既十字位越爛，現在已經上唔到，拆唔到個 binding， 點算呢？

As you have found out, the screws for your bindings are not "Philips" screws (NOT 十字螺絲) , you should not use Philips or nomal screwdriver, you need & use a #3 Pozidriv.

Now that the screws are damaged, I don't know what you can do, might be you have to drill it out and use "helicoil" to repair it. Good luck.

[sneaker]

剛換了一個大 d 既十字鑽咀，終於攪掂！如果唔係成日出 trip，都係建議每次回來後拆去 bindings，以免鏍絲鐵化，實得滯。:wall:

[Mike]

剛換了一個大 d 既十字鑽咀，終於攪掂！如果唔係成日出 trip，都係建議每次回來後拆去 bindings，以免鏍絲鐵化，實得滯。:wall:


Skis (not talking about skis with rails) are not like snowboard, they do not have cast-in inserts for screwing in the bindings. All holes have to be drilled.

Once you mounted the bindings onto the skis, normally you do NOT take them off.

Because of the materials used in maufacturing the skis and they do not have metal inserts for screws like the snowboard, if you need to re-mount the bindings using the same holes, you have to plug the holes first and then re-drill.

The screws come with the bindings, they are quite special, it is difficult to buy the screws separately.

[freeskier]

Skis (not talking about skis with rails) are not like snowboard, they do not have cast-in inserts for screwing in the bindings. All holes have to be drilled.

Once you mounted the bindings onto the skis, normally you do NOT take them off.

Because of the materials used in maufacturing the skis and they do not have metal inserts for screws like the snowboard, if you need to re-mount the bindings using the same holes, you have to plug the holes first and then re-drill.

The screws come with the bindings, they are quite special, it is difficult to buy the screws separately.

我估佢講緊snowboard binding 喎. 不過post錯咗topic. 如果係ski binding 嘅話. 咁我就真係孤陋寡聞. 因為聽都未聽過有人會成日將個binding又拆又裝. 大家千萬唔好學呀, 咪對ski會好快玩完.

不過就算snowboard binding都唔好成日拆喎, 啲screw 上面啲防滑塗料蝕咗, 啲screw會成日鬆, 又會唔見screw. 好麻煩.

[sneaker]

我估佢講緊snowboard binding 喎. 不過post錯咗topic. 如果係ski binding 嘅話. 咁我就真係孤陋寡聞. 因為聽都未聽過有人會成日將個binding又拆又裝. 大家千萬唔好學呀, 咪對ski會好快玩完.

不過就算snowboard binding都唔好成日拆喎, 啲screw 上面啲防滑塗料蝕咗, 啲screw會成日鬆, 又會唔見screw. 好麻煩.

噢！我情急下 post 錯左，係 snowboard 。

[Mike]

噢！我情急下 post 錯左，係 snowboard 。

When you re-mount your bindings on your SNOWBOARD, don't over-tighten the screws. If you over-tighten them by a lot or you are getting them cross threaded, you will strip-out the insert screws. The way to tighten a binding down is to rotate your tightening sequence much like when you change a tire. Snug them all down, then tighten in a pattern, progressively tightening each one. If you tighten down on one then go to the next, it can cause you to over-tighten.

Snowboard bindings do not need to be torqued down like a cylinder head bolt. just hand tight is all it takes and use a thin coating of the BLUE Locktite (not the red one) to prevent any loosening.